Top
MENU
Track my Order  |  My Account  |  0 item(s)    View Cart

Atlantic Color Changing Hardscape Lights Manual

ATLANTIC SOL COLOR CHANGING HARDSCAPE LIGHTS OPERATION MANUAL:

 
Atlantic color changing Led hardscape lights

Includes Models: SOLCCH06 - SOLCCH12 - SOLCCSL2

 

Atlantic Color Changing Hardscape Lights Operation Manual - Printable PDF Version

 

Introduction

Thank you for purchasing Color Changing SOL Lighting. Atlantic’s SOL Lighting features solid brass bodies with an oil-rubbed bronze finish. These LEDs create a vibrant nighttime atmosphere with 48 different colors and 18 different pre- programed color changing combinations. Multiple LEDs can be connected to run through one transformer and be controlled by one remote.

Installation

Spout Light Installation
The Spout Light can be installed behind a wall, shining through a wall spout

Atlantic color changing hardscape figure 1

(see Figure 1) or under a core-drilled stone or pot (see Figure 2). The light is designed to be installed in any tee that has 1” female threads. If the tee is larger than 1”, a reducing bushing with 1” female threads will be needed. Install the light in the back of the tee, with the light facing the water outlet. Apply a small amount teflon tape or paste to the threads of the light and thread the light into the fitting. Do not use the cord to twist in the light or allow it to become twisted when tightening. You can remove the driver from the cord when pulling it through conduit. Once the cord is through the conduit, reattach the driver before connecting the light to a power source. Failure to reattach the driver will damage the light and void warranty.

Hardscape Wall Light Installation

Hardscape Wall Lights are designed to be installed into walls and columns, just under the capstone. The LED light strip and driver can be replaced without removing the capstone. The cord between the driver connection and the light is approximately 19’, enabling the driver to be left outside of the column or wall for future access (see Figure 3). When laying the base course of stone, either notch the cord into the wall or leave a notch slightly larger than ¾” to pass the cord through. If multiple lights are going to be installed, the notch will need to be slightly larger to accommodate multiple cords. Removing the driver will allow the cord to be pulled through the notch; reattach the driver before connecting the light to a power source. Failure to reattach the driver will damage the light and void warranty.

Atlantic color changing hardscape figure 2

When installing the mounting bracket, make sure to notch the stone for the ¼”cord (see Figure 4). Test fit the mounting bracket and cord, so that it does not rock or put too much pressure on the cord. The holes in the bracket are for glue points to hold the capstone and bracket in place. The LED light strip can be replaced without removing the mounting bracket or capstone.

Atlantic color changing hardscape figure 3

Preset Light Changing Modes
Mode Selection

  • To switch to the Color Wheel: hold the A button for two seconds and the light will return to the last color displayed while in the Color Wheel mode. Run your finger around the color wheel to select a new color.
  • To switch to the Preset Light Changing Modes: hold the A button for two seconds, and the light will return to the last preset mode displayed while in the Light Changing Modes. Press the I and J button to switch between the different preset modes.
  • To switch to the Preset Light Changing Modes: hold the B button for three seconds or until the light changes to Crystal White. Press the D button, and the light will return to the last preset mode displayed while in the Light Changing Modes. Press the D and E button to switch between the different preset modes.

Changing the Brightness and Speed

In all modes, you can use the E and F keys to change the brightness of the light. In all modes, you can use the G and H keys to change the speed of the light transitions. There are 10 levels for each.

Synchronizing the Remote to the Control Unit

If the remote control stops working properly, please install fresh batteries. If prob- lems persist, the remote may need to be re-synced to the control module.

Follow the instructions below to re-sync the remote control:
1. Unplug the transformer.
2. Hold the E button down (The red indicator lamp on the remote will be blinking).
3. While still holding the E button down, plug in the transformer. The light will start blinking.

  • If the light blinks three times and stops, the remote and control unit are synchronized.
  • If the light blinks six or more times, it is clearing all codes. Repeat steps 1-3.

Maintenance

Spout Light Maintenance
Replacement LED Bulbs are available for SOL Color Changing Spout Lights.

Atlantic color changing hardscape figure 4

To loosen and tighten the brass lens ring on SOL Color Changing Spout Lights, use the included key. Simply place the key in the slots on the brass lens ring to loosen or tighten. Ensure that all components are installed correctly after servicing. Inspect the silicone gaskets for defects and proper placement before re-assembling. Ensure that the lens ring is tightly secured before submersing the fixture.

Hardscape Wall Light Maintenance - Replacing the LED Light Strip

Atlantic color changing hardscape figure 5

Make sure that the power is off before attempting to replace the light. Remove the screws on the existing light, being careful not to let the light strip fall, as this could break the plug connecting the light to the cord. Lower the light and squeeze the locking clip; this will allow the plug to be separated. Plug in the new light, making sure the gasket has not moved or shifted and that the notched edge of the light strip is between the two ridges on the cord gasket. Align the screw holes and hand tighten the screws.

Warranty

All SOL Lighting carries a five-year limited warranty. This limited warranty is ex- tended solely to the original purchaser commencing from the date of the original purchase receipt and is void if any of the following apply:

  • The cord has been cut or altered between the light body and the Control Module.
  • The light body / LED components have been misused or abused.
  • The light body / LED components have been disassembled or modified other than as described in this manual.
  • The Control Module and/or Remote Control have not been adequately protected from moisture.

Troubleshooting Guide

Always turn off power before inspecting the Color Changing Lights. Failure to observe this precaution can result in a serious accident.

Before ordering repairs, carefully read through this instruction booklet. If the problem persists, contact your dealer.

Problem Possible Cause Possible Solution
Remote is not working (no indicator light) No batteries / batteries dead Put in new batteries.
Remote is not working (indicator light is on) Remote is not synced with Control Module Refer to synchronizing the remote instructions
LED light will not illuminate No power to outlet
No power to LED
LED is broken / defective
Confirm power to outlet
Check all connections, ensure cord is not cut or damanged
Replace LED bulb
LED color differs from remote control Improper connection between LED light and control module
Controller failure
Inspect connection / align arrow on plugs
Contact Dealer for repair / replacement
Multiple lights display different colors when connected to the same splitter Improper connection between LED light and 3-way splitter
Faulty Splitter
Inspect connection / align arrow on plugs
Contact Dealer for repair / replacement