Atlantic Color Changing Colorfalls Operating Manual

Atlantic's Color Changing Colorfalls Operating Manual Includes Models: CC06 - CC12 - CC24 - CC36

Atlantic Color Changing Colorfall Operating Manual - Printable PDF Version

Introduction

Thank you for choosing Atlantic’s Color Changing Colorfalls. The Colorfalls are designed for use in Pond-free and fountain applications. The Color Changing Colorfalls feature a larger opening which produces a thicker water sheer and less clogging from debris in the water, a remote controlled Color Changing LED light bar, and a removable back plate that provides access to the interior of the spillway for easy maintenance and winterizing.

Prior to Operation and Installation
Caution:

DO NOT operate this product under any conditions other than those for which it is specified. Failure to observe these precautions can lead to electrical shock, product failure, or other problems.
Follow all aspects of electrical codes when installing the Color Changing Colorfalls.
To reduce the risk of electrical shock, connect only to a 110 volt receptacle protected by a ground fault circuit interrupter (GFCI).
The input power to the Color Changing Control Module is 12 volt AC. The Control Module can be connected to a larger outdoor lighting transformer; however this must be done between the Control Module and the transformer. Removing the Control Module or tampering with the cord between the Control Module and the Colorfalls will damage the light bar and void warranty.
The Control Module is weather resistant with an IP54 rating. Do not submerse the Control Module or expose it to heavy rainfall. It must be mounted off the ground close to the power source. Failure to do so will void the warranty.
Colorfalls are designed for use in Pond-free and fountain applications. Colorfalls are not intended for use in water gardens or any pond with plant or aquatic life.

The ColorFalls must be accessible for service and maintenance. Installing the ColorFalls so that the entire body is removable is highly recommended. Do not glue the cap stones above the ColorFalls or permanently mortar the ColorFalls in place.

The Colorfalls can support 40 lbs. per linear foot (e.g. a 24” Colorfalls can support 80 lbs.). If the weight on the weir exceeds that amount, you will need to provide a lintel support for the added weight. This support should still make contact with the weir to prevent it from shifting.

See the chart below for the recommended placement of the Colorfalls above the basin or pool. If the placement of the Colorfalls exceeds the recommended height, water loss will increase significantly due to splash and wind drift.

Colorfalls	Maximum Falls Height Above Basin	Flow Rate
CC06	18"	600 GPH
CC12	24"	1200 GPH
CC24	30"	2400 GPH
CC36	36"	3600 GPH

Installation of Color Changing Colorfalls

Atlantic Color Changing Colorfalls figure 1-2

The opening in the wall where the Colorfalls will be placed is important to the function of the Colorfalls. If it is not level and free of debris the Colorfalls will not function properly. The base of Colorfalls body as well as the bottom of the spillway lip must be supported by the opening in which it is placed. The Colorfalls Spillway must protrude from the wall a minimum of ½” and maximum of 1”. The top side of the opening must also be in contact with the Colorfalls to prevent it from shifting. See Figure 1 for the proper sizing of the opening for the Colorfalls.

Plumbing A Single Colorfalls

Each ColorFalls spillway is equipped with three convenient 1½” threaded inlets to accommodate 1½” Sch 40 MPT fittings. Choose one or more of the three inlets for plumbing: you can either plumb directly into the back center of the unit, or into both sides. (Plumbing the ColorFalls from one side only will produce an uneven water sheer. Feed lines must be connected to both sides to ensure an even water flow.) Close off the unused inlet(s) with the provided plugs. The plugs have O-ring seals and can be installed without thread sealant.

Installing a ball valve (not included) on the feed line between the pump and the Colorfalls is recommended for added control of water flow.

Plumbing Modular Colorfalls

Connect the Colorfalls together using the 1½” threaded connector (included). Begin by installing one end of the connector into the side inlet of one Colorfalls. Align the second Colorfalls and spin it onto the threaded fitting (screwing the two units together). Before they are completely tightened, install the double sided gasket (included) at the end of the end of the spillway between the units. This will create a watertight seal where the spillways meet. Pull the spillways of the Colorfalls apart while completing the final turn of the Colorfalls body. Once you have ensured proper alignment, press the spillways of the two units together (sandwiching the gasket) to ensure it is in contact with both units.

Atlantic Color Changing Colorfalls figure 2

When plumbing multiple Color Changing Colorfalls together, use the back center inlet on each individual Colorfalls, plugging the side inlets, regardless if you are using one pump or multiple pumps. This will balance the flow of water going to the falls.

Note: If plumbing two different sized Colorfalls together, a ball valve must be added on each vertical feed line to adjust the water flow into each unit.

Atlantic Color Changing Colorfalls figure 3

The individual feed lines to each Colorfalls should be 1½” PVC. If using one pump to feed multiple Colorfalls, the main feed line should be 2” or larger. The main feed line should be run horizontally along the back of the wall with vertical 1½” feed lines branching off to each Colorfalls (Figure 3).

Installation Requirements

1. The Control Module is weather-resistant with an IP54 rating. Do not submerse it or expose it to heavy rainfall. It must be mounted off the ground close to the power source. Failure to do so will void the warranty.

2. Remove the red protective cap from the top of the control module and install the antenna. Thread the black antenna on until snug, making sure it seals against the gasket.

3. Install the control box in a well ventilated area to ensure that the module operates in within its working temperature specified above.

4. Verify that the control module input voltage is 12 volt AC. We recommend that you use the transformer provided with this unit.

5. Ensure that all cable connections are secure.

6. Do not connect the power before the cord connections are finished.

7. Do not cut or alter the cord between the Colorfalls and the Control Module.

8. The remote control requires three (2) AAA batteries (not included). Do not touch the face of the remote while installing batteries.

Connecting the Light Bar

The Colorfalls light bar will not operate if plugs are aligned incorrectly. The six pronged connectors have raised arrows that indicate proper alignment. Follow the connecting chart below to connect all cables. Ensure that the unit is not plugged in while connecting

Atlantic Color Changing Colorfalls figure 4

Atlantic’s CCCM05 Master Controller (sold separately) enables up to five individual Color Changing light bars to be synchronized to change colors at the same time using one remote. In this application, only one Control Module and one remote are required. Use a Control Module and remote from any Colorfalls and it will control all light bars when used with the CCCM05 Master Controller. Replace the transformer from your Colorfalls with the 60 watt transformer from the Master Controller, and connect the 5-Way splitter supplied with the CCCM05 between the Control Module and the light bars. See the connecting chart below for details.

Atlantic Color Changing Colorfalls figure 5

Operation
Technical Data (Control Module)

Working Temperature: 0ºF -140ºF (-20°C - 60ºC)
Output: 3 circuits (R/G/B)
Input Power: AC12V
Output Power: DC12V, 80 watts max Output Current: 2A /circuit

Atlantic Color Changing Colorfalls figure 6

Mode Selection

To switch to the Color Wheel: hold the A button for two seconds and the light will return to the last color displayed while in the Color Wheel mode. Run your finger around the color wheel to select a new color.
To switch to the Preset Light Changing Modes: hold the A button for two seconds, and the light will return to the last preset mode displayed while in the Light Changing Modes. Press the I and J button to switch between the different preset modes.

Changing the Brightness and Speed

In all modes, you can use the E and F keys to change the brightness of the light. In all modes, you can use the G and H keys to change the speed of the light transitions. There are 10 levels for each.

Synchronizing the Remote to the Control Unit

If the remote control stops working properly, please install fresh batteries. If problems persist, the remote may need to be re-synced to the control module.

Follow the instructions below to re-sync the remote control.

1. Unplug the transformer.

2. Hold the E button down (The red indicator lamp on the remote will be lit).

3. While still holding the E button down, plug in the transformer. The Colorfalls will start blinking

If the Colorfalls blinks three times and stops, the remote and control unit are synchronized.
If the Colorfalls blinks six or more times, it is clearing all codes. Repeat steps 1-3.

Maintenance

Atlantic’s Color Changing Colorfalls has a removable back plate for easy cleaning of the interior of the spillway. To clean the interior of the spillway, simply remove the screws on the back plate and remove the baffle (Figure 4). Remove any large obstructions that may be present and wipe down the interior with a non-abrasive cloth. Once finished, install the baffle and re-attach the back plate, making sure that the gasket is in place to ensure a water-tight seal.

Caution: Be extremely cautious when tightening the screws. It is strongly recom- mended that you tighten the screws with a hand held screwdriver. Over tightening the screws could crack the back plate or strip the screw holes. The screws need only be snug for the gasket to make a seal.

For winterizing, loosen the screws on the back plate to allow excess water to drain. Once the water is removed from the interior of the spillway, retighten the screws.

Warranty

Colorfalls and all its components carry a one-year limited warranty. This limited warranty is extended solely to the original purchaser commencing from the date of the original purchase receipt and is void if any of the following apply:

The cord has been cut or altered between the Colorfalls and the Control Module.
The Colorfalls has been misused or abused
The Colorfalls has been disassembled or modified other than as described in this manual.
The Control Module and/or Remote Control have not been adequately protected from moisture.
This warranty excludes labor/costs of labor for removal or installation of any product.

Troubleshooting Guide

Always turn off power before inspecting the Colorfalls. Failure to observe this precaution can result in a serious accident.

Before ordering repairs, carefully read through this instruction booklet. If the problem persists, contact your dealer.

Problem	Possible Cause	Possible Solution
Remote is not working (no indicator light)	No batteries / batteries installed incorrectly	Put in new batteries.
Remote is not working (indicator light is on)	Remote is not synced with Control Module	Refer to page 6 of the manual
Diminished water flow	Pump blockage Obstruction in plumbing line	Clear debris from pump intake Check pump manual for cleaning Clear any debris from plumbing
Light bar will not illuminate	No power to outlet No power to Control Module No Power to Light Bar	Confirm power to outlet. Check all connections, ensure cord is not cut or damaged. Check all connections, ensure cord is not cut or damaged.
Light color is not synced with remote	The arrows on the plugs are not aligned.	Check connections, make sure they are properly aligned.
Water leaking from Colorfalls body	Bad plumbing connection Gasket out of place Screws in back plate are too loose	Inspect all plumbing & plugs. Ensure gasket in back plate is in proper position. Ensure screws are fully tightened.
Diminished water flow	Blocked pump intake Obstruction in plumbing line Debris in Colorfalls spillway	Clear debris from pump intake. Inspect plumbing line and clear any debris. Refer to Maintenance section on page 7.
Waterfall sheer is splitting	Debris in Colorfalls spillway	Refer to Maintenance section on page 7.